Menu
Lumenier LUX Mini F7 30A Stack
Lumenier LUX Mini F7 20×20 Stack (30A 2-6S ESC, F7 FC)
The Lumenier F7 Mini Stack gives you premium components in a featured-packed platform, all in a 20×20 stack!
***VTX not included***
115 $
Available on backorder
- SKU - 1234
Lumenier LUX Mini F7 30A Stack
Lumenier LUX Mini F7 20×20 Stack (30A 2-6S ESC, F7 FC)
The Lumenier F7 Mini Stack gives you premium components in a featured-packed platform, all in a 20×20 stack!
***VTX not included***
115 $
- SKU - 1234
Available on backorder
DESCRIPTION
About this product
The Lumenier F7 Mini Stack is the go-to 20×20 stack for all types of mini quads. The powerful F7 flight controller allows for simultaneous processes to be handled with ease, giving you a stable and clean signal to your sensors. The 2-6S 30A ESC features the latest gen. BLHeli_32 firmware running alongside an additional F3 processor to give you even more headroom.
this 20×20 stack will give any 30×30 stack a run for its money, and at a fraction of the size, weight, and cost!
LUX Mini F7
Features
- MCU: 216MHz STM32F722RET6
- IMU: ICM20602
- OSD: AB7456
- Blackbox: 128Mbit / 16MByte
- Anti-Vibration silicone grommets built-in
- 6x UARTs with built-in inversion
- 1x Softserial supported
- 1x I2C
- 1x SH1.0_8pin connector (Vbat/G/Curr/TLM/S1/S2/S3/S4)
- Vbat filtered output power for VTX
- Camera control
- Smartaudio & Tramp VTX protocol support
- WS2812 Led Strip support
- Beeper solder pad
- Input: 6~36V (2~8S LiPo)
- BEC: 5V 3A cont.
- LDO 3.3V: Max.200mA
Software/Hardware Features
- Betaflight support – target LUXMINIF7
- BLHeli passthrough flashing supported by hardware
Specifications
- High quality, gold plated PCB
- Micro USB connector for programming
- Dimensions: 28x28x6mm (includes USB in height)
- Mounting Holes: 20mm square to center of holes
- Weight: 5g
Razor ESC
Micro Razor 30A
Features
- New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
- Latest Gen. firmware using BLHeli_32 (Razor_32 target)
- Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us) and Multishot (5-25us). Auto-detection.
- Ultra-Lightweight (7.5g), and compact size
- Adaptive timing, compatible with a wide range of motors and Kv
- Synchronous rectification technology adds efficiency, damped light
- Powerful regenerative braking / active braking.
- 2-6s LiPo battery compatible
Specs
- Input: 2-6s LiPoly
- Constant: 30 Amps
- Burst: 40 Amps
- Dimensions: 32x36x5mm
- Mounting holes: 20×20 M3
- Signal wire: 7cm
- Weight: 7.5g
- 8pin connector pinout: VBAT, Ground, Current ADC, TLM, Motor 1, Motor 2, Motor 3, Motor 4
Features
- Compact 20×20 stackable design
- Mounts with M3 or M2 hardware
- Conformal coated for added protection
- Optional protective cover included
- Downloads
